Apple MPEG Media SystemInstallation Guide
5Installing the MPEG CardTo install the MPEG card in a computer with a separatemonitor, follow these steps:1 Turn off the computer.You can do this by
4 Pulling gently, swing the panel down and slip it out.5 If there are security screws on the vertical plate on the backof the computer, remove them wi
7 Swing the handle out from its storage position, then graspthe handle and gently but firmly pull it toward you.The vertical plate and the logic board
10 Plug the MPEG card, component side down, into theprocessor-direct slot on the logic board. Make sure the cardis firmly seated in the slot.Processor
9Installing the MPEG Card11 Attach the other end of the ribbon cable to the Digital Audioand Video (DAV) connector on the video input card.continues .
12 Slip the base of the logic board into the guide rails inside thecomputer case and swing the handle back into its storageposition.13 Press the reset
11Installing the MPEG Card14 If you removed security screws, reinsert and tighten themnow.15 Fit the hooks at the base of the plastic back panel into
16 Swing the plastic back panel up and snap it into place.17 Reconnect the power cord and any cables you disconnectedat the start of this process.To r
13Installing the MPEG CardStyle BStyle A
14Installing the MPEG CardInstalling the card in Style A1 Turn off the computer.m Choose Shut Down from the Special menu, or press thePower key on the
K Apple Computer, Inc.© 1995 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, w
15Installing the MPEG Card4 Locate the two latches on the underside of the computer’scase with your fingertips.continues .Locate the two latches on th
5 Pulling gently, swing the panel up and slip it out.Remember: Don’t walk around the room until you havefinished installing the card and closed the c
6 There is a wire handle on the back of the logic board. Swingit down and use it to pull the logic board toward you. The logic board is plugged into a
8 Set the MPEG card down, component side up, and attacheither end of the ribbon cable to the shorter of the twoconnectors on the card, as shown. 9 Plu
10 Attach the other end of the ribbon cable to the Digital Audioand Video (DAV) connector on the video input card.continues .Video input card DAV conn
11 Swing the wire handle on the logic board back up into itsstorage position, securing it under its catch. Then fit thelogic board into the guide rail
21Installing the MPEG Card12 Press the reset button on the right side of the logic board,then gently but firmly push the board back into place withint
13 Fit the tabs at the top of the back panel into the case.14 Snap the bottom of the panel into place, making sure it isflush with the back of the com
15 Reinsert the security screws on either side of the back panel.16 Reconnect any cables you disconnected at the start of thisprocess.To reset the sys
2 Unplug all the cables except the power cord from yourcomputer.Leaving the power cord plugged in helps protect thecomputer from electrostatic dischar
Communications regulation information ivIntroduction 11 What you should have 22 Installing the MPEG card 3Installing the card in a modular com
4 Pulling gently, swing the panel down and slip it out.continues .25Installing the MPEG Card
5 Remove both retainer screws from the vertical plate behindthe back panel.Remember: Don’t walk around the room until you havefinished installing the
6 There is a wire handle on the back of the logic board. Swingit down and use it to pull the logic board toward you.The logic board is plugged into a
8 Set the MPEG card down, component side up, and attachone end (either end) of the ribbon cable to the shorter ofthe two connectors on the card, as sh
29Installing the MPEG Card10 Attach the other end of the ribbon cable to the Digital Audioand Video (DAV) connector on the video input card.continues
30Installing the MPEG Card11 Swing the wire handle on the logic board back up into itsstorage position, securing it under its catch. Then fit thelogic
31Installing the MPEG Card12 Press the reset button on the logic board, then gently butfirmly push the board back into place within the computer.You w
32Installing the MPEG Card13 Reinsert the retainer screws into the vertical plate on thelogic board.Reinsert both retainer screws into the vertical pl
33Installing the MPEG Card14 Slip the tabs at the bottom of the back panel into thematching grooves in the computer case. Then press downon the clips
34SECTION3Installing the SoftwareThe Apple Video Player application program lets you watchvideo on your computer. Your computer probably alreadyhas a
Communications regulation informationFCC statementThis equipment has been tested and found to comply with the limits for a Class Bdigital device in ac
Follow these steps to install the software.1 Start up your computer.2 Press the Open/Close button on your CD-ROM drive to openthe tray.3 Place the App
Below is a short introduction to starting Apple Video Playerand playing digital movies. For these steps, you need to haveone of the MPEG CDs that came
3 Click the movie projector icon in the Controls window.The Controls window appears and, in a moment, displaysplayback controls and a pull-down menu o
5 Click the Play button.After a moment, the movie should start playing in the Moviewindow.You can experiment with the playback controls and with themo
39SECTION5Technical Informationm 24-bit color displaym NTSC video playback: 30 frames per second m PAL video playback: 25 frames per second m Film pla
Apple Computer, Inc.1 Infinite LoopCupertino, California 95014-2084408.996.1010030-7406-APrinted in U.S.A.AppMeInstalla
This product was tested for FCC compliance under conditions that included the use ofshielded cables and connectors between system components. It is im
1INTRODUCTIONWith the Apple MPEG Media System and the Apple VideoPlayer System or TV/Video Player System installed, you canwatch MPEG-compressed digit
2SECTION1What You Should HaveCheck your package to make sure you have both the MPEGcard and a ribbon cable.MPEG card Ribbon cable
3SECTION2Installing the MPEG CardBefore you can install the MPEG card, the video input card(which comes with the Apple Video System and AppleTV/Video
m alert soundm default highlight colorm default AppleTalk or network connectionThe next time you start your computer, you’ll probably wantto reset the
Commentaires sur ces manuels