Apple Xserve (Early 2008) DIY Procedure for Power Distri Manuel d'utilisateur télécharger pdf

 Xserve (Late 2006/Early 2008)

073-1103 Rev. B

Power Distribution Board

Replacement Instructions

Follow the instructions in this document carefully. Failure to follow these instructions could

damage your equipment and void its warranty.

Online instructions are available at http://www.apple.com/support/diy/.

Working Safely Inside the Xserve

Always touch the Xserve enclosure to discharge static electricity before you touch any

components inside the Xserve. To avoid generating static electricity, do not walk around the

room until you have nished working inside the server and have replaced the cover. To minimize

the possibility of damage due to static discharge, wear an antistatic wrist strap while you work

inside the Xserve.

Warning: Always shut down the Xserve and disconnect the power cords before opening

it to avoid damaging its internal components or the components you are installing. Don’t

open the server while it is turned on. Even after you shut down the Xserve, its internal

components can be very hot. Let it cool before you open it.

Tools Required

The only tool required for this procedure is a Phillips #1 screwdriver. You may also nd a small

atblade screwdriver useful in releasing the connectors on the power distribution board cable.

Removing the Xserve from a Rack

Alert users that the server will be unavailable for a period of time. 1.

Shut down the Xserve (see the Xserve User’s Guide for help) and then wait to let the Xserve 2.

internal components cool.

Warning: Always shut down the Xserve before opening it to avoid damaging its internal

components or the components you want to install or remove. Don’t open the Xserve

or try to install or remove items inside while it is turned on. Even after you shut down

the Xserve, its internal components can be very hot. Let it cool down for 5 to 10 minutes

before you open it.

1 2 3 4 5 6 ... 13 14

Résumé du contenu

Page 1 - Power Distribution Board

 Xserve (Late 2006/Early 2008)073-1103 Rev. BPower Distribution BoardReplacement InstructionsFollow the instructions in this document carefully. Fail

Page 2 - Opening the Xserve

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 10Installing the Replacement Power Distribution BoardLower the replac

Page 3 - Power Supplies

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 11Replacing the Drive Interconnect BackplaneLower the backplane into

Page 4

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 12Tighten the thumbscrew that secures the backplane to the enclosure.

Page 5 - Airow Duct

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 13Tighten the ve Phillips screws that fasten the airow duct to the

Page 6 - Fan Array

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 14Closing the XserveReplace and secure the cover.1. Slide the Xserve

Page 7 - Drive Interconnect Backplane

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 2Unplug all cables from the Xserve. 3. Note: If you have trouble rele

Page 8

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 3Removing the Installed Power Distribution BoardNote: Before removing

Page 9

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 4Power Distribution Board CableLocate the power distribution board ca

Page 10

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 5Caution: The power distribution board cable connectors are tight and

Page 11

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 6Fan ArrayLoosen the two thumbscrews that secure the fan array to the

Page 12 - Replacing the Airow Duct

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 7Drive Interconnect BackplaneRelease the two locking levers on the fr

Page 13 - Replacing the Power Supplies

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 8Shift the backplane to the left (towards the enclosure side), in the

Page 14 - Closing the Xserve

Xserve (Late 2006/Early 2008) Power Distribution Board Replacement Instructions 9Power Distribution BoardLocate the power distribution board. 1. Rele

Plus de documents pour Logiciel Apple Xserve (Early 2008) DIY Procedure for Power Distri

Voir le document Apple Xserve (Early 2008) DIY Procedure for Power Distri Manuel d'utilisateur

Apple Xserve (Early 2008) DIY Procedure for Power Distri Manuel d'utilisateur (4 pages)

Commentaires sur ces manuels

Pas de commentaire

Apple Xserve (Early 2008) DIY Procedure for Power Distri Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Logiciel Apple Xserve (Early 2008) DIY Procedure for Power Distri. Apple Xserve (Early 2008) DIY Procedure for Power Distribution Board User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Logiciel Apple Xserve (Early 2008) DIY Procedure for Power Distri

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Apple Xserve (Early 2008) DIY Procedure for Power Distri