Apple Xserve Intel (Late 2006) DIY Procedure for Front P Manuel d'utilisateur télécharger pdf

 Xserve (Late 2006)

073-1101 Rev. A

Front Panel Board

Replacement Instructions

Follow the instructions in this document carefully. Failure to follow these instructions could

damage your equipment and void its warranty.

Online instructions are available at http://www.apple.com/support/diy/.

Working Safely Inside the Xserve

Always touch the Xserve enclosure to discharge static electricity before you touch any

components inside the Xserve. To avoid generating static electricity, do not walk around the

room until you have nished working inside the server and have replaced the cover. To minimize

the possibility of damage due to static discharge, wear an antistatic wrist strap while you work

inside the Xserve.

Warning: Always shut down the Xserve and disconnect the power cords before opening

it to avoid damaging its internal components or the components you are installing. Don’t

open the server while it is turned on. Even after you shut down the Xserve, its internal

components can be very hot. Let it cool before you open it.

Tools Required

The only tool required for this procedure is a Phillips #1 screwdriver.

Removing the Xserve from a Rack

Alert users that the server will be unavailable for a period of time.

Shut down the Xserve (see the Xserve User’s Guide for help) and then wait to let the Xserve

internal components cool.

Warning: Always shut down the Xserve before opening it to avoid damaging its internal

components or the components you want to install or remove. Don’t open the Xserve

or try to install or remove items inside while it is turned on. Even after you shut down

the Xserve, its internal components can be very hot. Let it cool down for 5 to 10 minutes

before you open it.

1 2 3 4 5 6 7

Résumé du contenu

Page 1 - Front Panel Board

 Xserve (Late 2006)073-1101 Rev. AFront Panel BoardReplacement InstructionsFollow the instructions in this document carefully. Failure to follow thes

Page 2 - Opening the Xserve

Xserve (Late 2006) Front Panel Board Replacement Instructions 2Unplug all cables from the Xserve. Note: If you have trouble releasing a cable from th

Page 3 - Locking Mechanism Rod

Xserve (Late 2006) Front Panel Board Replacement Instructions 3Removing the Installed Front Panel BoardNote: Before removing the front panel board, y

Page 4

Xserve (Late 2006) Front Panel Board Replacement Instructions 4Release the two locking levers on the front panel board cable connector and disconnect

Page 5

Xserve (Late 2006) Front Panel Board Replacement Instructions 5Slide the board back slightly and release the two clips on either side of it. Tilt the

Page 6 - Closing the Xserve

Xserve (Late 2006) Front Panel Board Replacement Instructions 6Replacing the Locking Mechanism RodInsert the key-hole end of the rod into the port on

Page 7

Plus de documents pour Logiciel Apple Xserve Intel (Late 2006) DIY Procedure for Front P

Voir le document Apple Xserve Intel (Late 2006) DIY Procedure for Front P Manuel d'utilisateur

Apple Xserve Intel (Late 2006) DIY Procedure for Front P Manuel d'utilisateur (7 pages)

Commentaires sur ces manuels

Pas de commentaire

Apple Xserve Intel (Late 2006) DIY Procedure for Front P Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Logiciel Apple Xserve Intel (Late 2006) DIY Procedure for Front P. Apple Xserve Intel (Late 2006) DIY Procedure for Front Panel Board User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Logiciel Apple Xserve Intel (Late 2006) DIY Procedure for Front P

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Apple Xserve Intel (Late 2006) DIY Procedure for Front P