Apple Processor Cage and Clips Guide d'installation Page 71
- Page / 117
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Table 13 SP and Storage System Software Installation Checklist (continued)
Date and time:
Enter manually
Use NTP server information
Time Zone
New password to assign setupusr (for use with the system setup wizards)
NOTE: All passwords for the setupusr username must be between 7 and 32
characters in length and can consist of alphanumeric characters and the following
special characters: period (.), plus (+), dash (-), equal (=), and forward slash (/).
New password to assign 3parcust to access Service Processor Onsite Customer
Care (SPOCC)
NOTE: All passwords for the 3parcust username must be between 7 and 32
characters in length and can consist of alphanumeric characters and the following
special characters: period (.), plus (+), dash (-), equal (=), and forward slash (/).
HP 3PAR Storage System
StoreServ serial number
NOTE: The serial number is located on the back of your HP 3PAR storage system
next to the power switch for the node enclosure PCM, and it begins with16 (for
example, 1624635).
StoreServ system name
IP address (IPv4 only)
Subnet mask
Gateway IP address
Date and time:
Use one of the following methods to configure the date and time:
• Copy from SP
• Enter manually or use NTP server information
• Time Zone
New password to assign 3paradm (to access the storage system)
NOTE: Passwords for the 3paradm username can include all printable characters
and be between 6-8 characters in length.
HP 3PAR SmartStart
Performing host configurations after using SmartStart for installation setup requires
an available server to run Microsoft Windows 2008 R2, x64 Edition or 2012.
Storage System Software Installation Checklist 71
- Storage Installation Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 1 General Site Planning 6
- Acclimatization 8
- 2 Getting Started 9
- Inspecting the Packaging 10
- Storage System Installation 11
- Disk Drive Numbering 12
- Controller Nodes 13
- I/O Modules 17
- Power Cooling Modules 17
- Service Processor 19
- Power Distribution Units 19
- Important Safety Information 20
- Required Tools 21
- Additional requirements 21
- Configurations 21
- • 1U and 0U configurations 22
- Hardware Installation 23
- Hardware Installation 25 25
- Installing the 1U and 0U PDUs 27
- • 0U bracket installation 28
- 3. Install cage nuts 28
- Securing the Cables 29
- Installation is complete 30
- Unpacking the Cabinet 31
- Positioning the Cabinet 31
- Verify the Cabling 32
- Removing the Brackets 34
- Installing the Rail Kit 35
- Installing the Rail Kit 37 37
- Installing Enclosures 38
- (LFF) disk drive) 40
- Installing a Disk Drive 41
- NoneRound hole 43
- NoneSquare hole 43
- ScrewdriverThreaded hole 43
- • Screwdriver 44
- 7 Cabling the Storage System 50
- Cabling Expansion Cabinets 51
- Cabling the Service Processor 52
- Cabling the Power Strips 53
- Verifying Setup 54
- Verifying LED Status 56
- Figure 37 Disk Drive LEDs 57
- Table 9 PCM LED Descriptions 58
- Node Interconnect Ports 60
- Drive Enclosure LEDs 61
- Figure 42 Front Panel LEDs 62
- Table 11 Front panel LEDs 62
- Figure 43 Rear Panel LEDs 63
- Table 12 Rear panel LEDs 63
- Prerequisites for Using a VSP 64
- Deploying the VSP OVF File 65
- Launching HP 3PAR SmartStart 72
- Generate Service Processor ID 75
- Configure SP Networking 76
- Remote Support 77
- System Support Information 79
- Time and Region 80
- Change Passwords 81
- Applying Settings 83
- Figure 57 Apply Settings 84
- Verify Storage System 88
- Configure Networking 89
- ◦ Subnet Mask 89
- ◦ Gateway 89
- Configuring Time 89
- Figure 65 Configure Time Page 90
- Change Password 91
- Verify Configuration 92
- Progress 92
- Figure 68 Progress Page 93
- Figure 69 Results Page 93
- Contacting HP 95
- HP 3PAR documentation 95
- Typographic conventions 98
- HP 3PAR branding information 98
- 12 Documentation feedback 99
- Figure 74 7000 Series PCM 101
- Figure 75 M6700 Series PCM 102
- Figure 77 SFF Drive Assembly 102
- Figure 79 LFF Drive Assembly 103
- Accessory Kits 104
- Rail Kits 104
- Rail Kits 105 105
- Figure 87 M5 Cage Nut 106
- Adding Disk Drives 110
- Checking Progress 111
- Completing the Upgrade 112
- SmartStart is Unavailable 113
- E Validating Remote Support 114
- G Troubleshooting 117
© 2020, manymanuals.fr. Tous droits réservés | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels